Posted in Exquisite jewelry

As long as the watch is the name of the watch on the head there will be an icon, this and the car

As long as the watch is the name of the watch on the head there will be an icon, this and the car, watch the logo LOGO must play in the face of the eye, LOGO are generally graphics, but also English letters, such as the full name of the watch Or abbreviation or prefix. Table head of the icon can be considered a beautiful watch “landscape”, on behalf of the original original, Seiko secret agents; counterfeit false watch is often in this subtle place to do bad, fuzzy rough is a common problem.
Rolex watches watch the head of the icon and meaning
Oyster case with Rolex watches, excellent waterproof performance, this is also the structure of the watch table, because only watch the watch is a moving parts, it needs to be often operated, so this place is particularly important seal. Rolex watches are equipped with a screw lock lock structure, tighten the seal will be like a stopper; and here the waterproof seal apron at least two; like the green water ghost (16610LV model) and Dieton series of imitation Cartier love bracelet watches , Waterproof seal apron up to 3 heavy, an increase in the watch case on the outside of the handle tube, pull out the table can see. In the Rolex watch table head, there will be some logo, logo on the Rolex crown GOLO below, with a dot or dash line that there are two, there are two, there are three, these signs represent Watch the case of the material, but also represents the watch case and the handle of the structure. (See photo)
The specific meaning of the logo
Rolex watches watch the head of the icon and meaning
1, a dot on behalf of the watch is PT950 platinum case, the proportion of this precious metal, watch up to compare the pressure hand;
2, two representative of the origin of the watch with 18K white gold or gold case;
3, the three origin can also be understood as a triple waterproof, with such a table of the watch, handle the head tube visible waterproof seal ring. On the basis of triple waterproofing, if the watch case material uses platinum, then the middle of its three origin which will be smaller (see the relevant photos of the first six); if the watch case material using 18K white gold, then its 3 sides of the origin will be relatively small (see the relevant photo of the first five). When the three origin is generally large (see the relevant photo of the first four), the situation is equivalent to the use of dash, usually case material for the 18K gold, 18K gold + stainless steel or pure stainless steel.
4, there is a short line of the most, dash as if it is a “wildcard”, on behalf of the watch is a double waterproof, table for the material for the 18K gold, 18K gold + stainless steel, or pure stainless steel, , This configuration is the most common.
How to buy a good mechanical watch? Watch is a sophisticated timing instrument, the price is higher, the use of time is also long. Watch the quality of good or bad, the user is very concerned about the problem. Therefore, people in the purchase of watches is always better, so good in the selection. But how can we pick a satisfactory quality watch? Usually, people only listen to the machine when the sound of the size of the sound to determine the quality of the watch is good or bad, it is unscientific. Because the quality of the watch is good or bad, mainly to see the actual travel time accuracy. When the machine moves, the sound is balanced, clear and no noise, only that the table machine is not faulty, and can not explain the quality of the watch is good or bad as the only way to pick the watch. It must also be selected from the following:
First, check the watch appearance parts
Watch the appearance from the shell, table mirror, dial and minutes and seconds and other Replica Cartier jewelry aspects of inspection. The case should be no trachoma and obvious scratches, angular symmetry; back cover and the shell of the rotation should be tight; two watch rings and the case of the same distance, the installation of the hole should be in the foot of the shell position The needle is not easy to fall off; table mirror should be no defects and scratches, transparent and bright; three-pin installation is correct, the needle and the needle, between the mirror and the dial should have the correct safety gap; dial and Pointer coating finish is good, no mark, dial scale line or luminous point integrity; head and case between about 0.1-0.3mm gap.
Second, check the sensitivity of the watch
The sensitivity of the watch is the flexibility of its balance wheel. Check the method is:
(1) will not have been on the winding has been moving around the watch gently shake, with the power to shake to observe the second hand moving situation: If the second hand in a very short period of time to stop walking, then the watch on the hair If the second hand to continue to move for a long time, then the watch can not be fully finished foot on the foot (that is, the winding also stored torque), the sensitivity is not high Or the table is faulty.
(2) will not have to stop the clockwork on the watch, slowly turn the head, observe the second hand to start the situation: the less the rotation of the article, the second hand to start the earlier the higher the sensitivity of the table; Or table machine has other failures. But pay attention to the wings of the watch because of the greater the stiffness of the hairspring than the traditional frequency (18000 times / hour) of the table machine to a little more winding on the swing. High sensitivity of the watch, on the foot after a winding time to move longer.
Third, check the pointer pointer spacing and location
Between the table and the table mirror, between the dial and between the three pins should maintain a certain spacing, or mutual collision caused by the normal operation of the table. Inspection can be observed by dialing. The position of the hour hand and the minute hand and the mutual check is normal check method is: the minute hand and hour hand to 3:00, 9:00, observe whether the two needle at right angles; dial to 6 points, whether the needle is a straight line; dial 12 points, Whether the two fingers coincide.
Fourth, check the watch on the body
Normal watch on the article should be easy www.ourlovestore.com . Turn the head of the article, the first feel more loose, gradually more tight, when you can not continue to turn forward the head, indicating that the winding has been completely full and the work of the normal work. If you turn the handle when the head of the article, the occurrence of “Cha Cha abnormal sound, or produce teeth and other teeth and other phenomena, then the above mechanism is faulty.
5, check the dialing machine
Watch the needle should be flexible, reliable and pointer rotation evenly. Inspection should focus on check the wheel and the central wheel friction with the tightness. In the dial, if there is no loose or tight feeling, indicating the sub-wheel friction normal and refueling amount, on the contrary, dial machine parts are faulty. The above method of buying a new watch, for the old watch or repair the quality of the inspection can also refer to, but according to the use of the watch as appropriate to reduce the standard.